Billion BiPAC 7800(N) Instrukcja Użytkownika

BiPAC 7800(N)X(L) 3G/4G LTE (Wireless-N) (VPN) ADSL2+/Fibre Broadband Router User Manual Version

5 • MAC Encapsulated Routing (RFC 1483 MER) • OAM F4 / F5 IPTV Applications*2 • IGMP Snooping and IGMP Proxy • MLD Snooping and MLD Proxy • Virtual

95 4. The client’s SSID and security settings will now be configured to match the SSID and security settings of the registrar. You can check the m

96 Configure AP as Enrollee Add Registrar with PIN Method 1. Set AP to “Unconfigured Mode” and Click “Config AP” button.

97 2. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number (76229909 (device) for ex

98 3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar. 4. Do Web Page

99 MAC Filter Select SSID: select the SSID you want this filter applies to. MAC Restrict Mode:  Disable: disable the MAC Filter function.  Allo

100 Wireless Bridge WDS (wireless distributed system) is a wireless access point mode that enables wireless link and communication with other access

101 Remote Bridge MAC Address: select the remote bridge MAC addresses.  Disable: Does not restrict the gateway communicating with bridges that ha

102 Advanced Here users can set some advanced parameters about wireless. Band: select frequency band. Here 2.4GHz. Channel: Allows channel selection

103 RIFS Advertisement: Reduced Inter-frame Spacing (RIFS) is a 802.11n feature that also improves performance by reducing the amount of dead time re

104 Station Info Here you can view information about the wireless clients. MAC Address: The MAC address of the wireless clients. Associated: List a

6 Management • Easy Sign-on (EZSO) • Web-based GUI for remote and local management (IPv4/IPv6) • Firmware upgrades and configuration data upload and

105 WAN-Wide Area Network A WAN (Wide Area Network) is a computer network that covers a broad geographical area (eg. Internet) that is used to conne

106 PPPoE PPPoE (PPP over Ethernet) provides access control in a manner which is similar to dial-up services using PPP. VCP/VPI: Enter the VCI/VPI

107 IPv4 Address: Select whether to set static IPv4 address or obtain automatically. IP Address: If Static is enabled in the above field, enter the s

108 Default Gateway Select default gateway for you connection (IPv4 and IPv6). DNS Either IPv4 or IPv6, you can choose static setting or select fro

109 Here you can configure WAN Service, if it is OK, you can access the internet. You can go to Status >WAN or Summary to view the WAN connection

110 PPPoA VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. De

111 MTU: Maximum Transmission Unit, the size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the int

112 IP over Ethernet VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, o

113 Option 125: Option 125 is a complementary standard of DHCP protocol, it is used to encapsulate option 125 message into DHCP offer packet before f

114 IPoA VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. D

7 Hardware Specifications Physical Interface • WLAN: 2 x 4dbi detachable antennas (BiPAC 7800NX(L) only) • DSL: ADSL port • USB 2.0 port for storage

115 Bridging VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MU

116  Ethernet Ethernet WAN connection is well known as directly broadband WAN connection. PPPoE Description: User-defined description for the

117 Username: Enter the account obtained from the ISP. Password: Enter the password obtained from the ISP. Service Name: The item is for identificat

118 Click Next to continue to set the default gateway and DNS for IPv4 and IPv6. Default Gateway Select a default gateway for you connection (IPv4

119 If you don’t need the service, select the item you want to remove, check the checkbox, then press Remove, it will be OK. Press Edit button to re-

120 IP over Ethernet Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates

121 WAN IP Address: Enter your IPv4 address to the device provided by your ISP. WAN Subnet Mask: Enter your submask to the device provided by your IS

122 Bridging Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates the fr

123  3G/LTE Select 3G/LTE to configure the route to enjoy the mobility. By default the 3G/LTE interface is on, user can edit the parameters to meet

124 service provider. APN: An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS call. The service provider is able to attac

8 Chapter 2: Installing the Router Package Contents 7800NXand7800NXL• BiPAC 7800NX(L) 3G/4G LTE Wireless-N ADSL2+ (VPN)/ Fibre Broadband Router

125 Here you can configure WAN Service, if it is OK, you can access the internet. You can go to Status >WAN or Summary to view the WAN connecti

126 DSL This screen allows you to set DSL parameters. DSL knowledge is required to configure these settings. Contact your ISP to make sure that these

127 SNR Signal-to-noise ratio (often abbreviated SNR or S/N) is a measure used in science and engineering that compares the level of a desired signa

128 System Internet Time The router does not have a real time clock on board; instead, it uses the Network Time Protocol (NTP) to get the most curre

129 Firmware Upgrade Software upgrading lets you experience new and integral functions of your router. Restart device with:  Factory Default Set

130 Backup / Update These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore from a previously

131 Access Control Access Control is used to prevent unauthorized access to the router configuration page. Here you can change the login user password

132 Mail Alert Mail alert is designed to keep system administrator or other relevant personnel alerted of any unexpected events that might have occur

133 Configure Log Log: Enable or disable this function. Log level: Select your log level. The log level allows you to configure which types of event

134 USB Storage here refers to network sharing in the network environment, USB devices act as the storage carrier for DLNA, common file sharing. St

9 7800X • BiPAC 7800X 3G/4G LTE ADSL2+ VPN/ Fibre Broadband Router • Quick Start Guide • CD containing the on-line manual • RJ-45 Cat. 5e STP Ether

135 User Account Users here can add user accounts for access to the storage, in this way users can access the network sharing storage with the specifi

136 Accessing mechanism of Storage: In your computer, Click Start > Run, enter \\192.168.1.254

137 When accessing the network storage, you can see a folder named “public”, users should have the account to enter, and the account can be set at the

138 Access the folder public.

139 When successfully accessed, the private folder of each user is established, and user can see from the following picture. The test fold in the pict

140 Print Server The Print Server feature allows you to share a printer on your network by connecting a USB cable from your printer to the USB port o

141 Step 2: Click ‘’Add a Printer’’. Step 3: Click “Add a network, wireless or Bluetooth printer

142 Step 4: Click “The printer that I want isn’t listed” Step 5: Select “Select a shared printer by name” Enter http://7800NX- LAN-IP:631/

143 Step 6: Click “Next” to add the printer driver. If your printer is not listed and your printer came with an installation disk, click “Hav

144 Step 8: Click “Next” and you are done You will now be able to see your printer on the Devices and Printers Page

10 Important note for using this router Warning 1. Do not use the router in high humidity or high temperatures. 2. Do not use the same power sour

145

146 DLNA The Digital Living Network Alliance (DLNA) is a non-profit collaborative trade organization established by Sony in June 2003, which is respo

147 Take Windows media player in Windows 7 accessing the DLNA server for example for usage of DLNA .

148 IP Tunnel An IP Tunnel is an Internet Protocol (IP) network communication channels between two networks of different protocols. It is used to tra

149 Associated WAN Interface: The applied WAN interface with the set tunnel, thus when there are packets from/to the WAN interface, the tunnel would b

150 IPv4inIPv6 4in6 refers to tunneling of IPv4 in Ipv6. It is an inherent internet interoperation mechanism allowing IPv4 to be used in an IPv6 only

151 Security IP Filtering Outgoing IP filtering enables you to configure your router to block specified internal/external users (IP address) from I

152 Destination Port [port or port: port]: Traffic with the particular set destination port or port in the set port range is to be blocked from going

153 IP Filtering Incoming Incoming IP Filtering is set by default to block all incoming traffic, but user can set rules to forward the specific incom

154 Time Schedule: Select or set exactly when the rule works. When set to “Always On”, the rule will work all time; and also you can set the precise t

11 Device Description The Front LEDs 7800X LED Status Meaning Red Boot failure or in emergency mode 1 Power Green System ready Green Transmi

155 MAC Filtering MAC Filtering is only effective on ATM PVCs configured in Bridged mode. FORWARDED means that all MAC layer frames will be forwarde

156 Blocking WAN PING This feature is enabled to let your router not respond to any ping command when someone others “Ping” your WAN IP.

157 Time Restriction A MAC (Media Access Control) address is the unique network hardware identifier for each PC on your network’s interface (i.e. its

158 An example: Here you can see that the user “child_use” with a MAC of 18:a9:05:04:12:23 is blocked to access the router from 00:00 to 23:59 Monda

159 URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.abcde.com or http://www.example.com) filter rules allow you

160 Keywords Filtering Note: Maximum number of entries: 32. Click to add the keywords. Enter the Keyword, for example image, and then click A

161 Filtering. Exception IP Address In the section, users can set the exception IP respectively for IPv4 and Ipv6. Click to add the IP Addresses

162 QoS - Quality of Service QoS helps you to control the data upload traffic of each application from LAN (Ethernet) to WAN (Internet). This feature

163 DSCP value. IP Precedence and DSCP Mapping Table Mapping Table Default (000000) Best EffortEF(101110) Expedited Forwarding AF11 (001010) Assured

164 Time Schedule: Select or set exactly when the rule works. When set to “Always On”, the rule will work all time; and also you can set the precise t

12 7800NXand7800NXL LED Status Meaning Red Boot failure or in emergency mode 1 Power Green System ready Green Transmission speed hitting

165 Examples: Common usage 1. Give outgoing VoIP traffic more priority. The default queue priority is normal, so if you have VoIP users in your

166 3. If you are actively engaged in P2P and are afraid of slowing down internet access for other users within your network, you can then use QoS to

167 NAT NAT (Network Address Translation) feature translates a private IP to a public IP, allowing multiple users to access the Internet through a si

168 The following configuration page will appear to let you configure. Interface: select from the drop-down menu the interface you want the virtual

169 Set up 1. Select a Server Name from the drop-down menu, then the port will automatically appear, modify some as you like, or you can just leave

170 Remove If you don’t need a specified Server, you can remove it. Check the check box beside the item you want to remove, then press Remove, it wil

171 Port Triggering Port triggering is a way to automate port forwarding with outbound traffic on predetermined ports (‘triggering ports’), incoming

172 Open port  Start: Enter a port number as the open port staring number.  End: Enter a port number as the open port ending number. Any port in t

173 Remove If you don’t need a specified Server, you can remove it. Check the check box beside the item you want to remove, and then press Remove.

174 DMZ Host The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming pac

13 The Rear Ports 7800X Port Meaning 1 Power Switch Power ON / OFF switch. 2 Power Connect the supplied power adapter to this jack. 3 RESET

175 One-to-One NAT One-to-One NAT maps a specific private/local address to a global/public IP address. If user has multiple global/public IP addresses

176 Wake On LAN Wake on LAN (WOL, sometimes WoL) is an Ethernet computer networking standard that allows a computer to be turned on or woken up remot

177 Advanced Setup There are sub-items within the System section: Routing, DNS, Static ARP, UPnP, VPN (7800NX and 7800X only), Certificate, Multicast,

178 Routing Default Gateway WAN port: Select the port this gateway applies to. To set Default Gateway and Available Routed WAN Interface. This in

179 Static Route With static route feature, you can control the routing of all the traffic across your network. With each routing rule created, you c

180 In listing table you can remove the one you don’t want by checking the checking box and press Remove button.

181 Policy Routing Here users can set a route for the host (source IP) in a LAN interface to access outside through a specified Default Gateway or a

182 RIP RIP, Router Information Protocol, is a simple Interior Gateway Protocol (IGP). RIP has two versions, RIP-1 and RIP-2. Interface: the interf

183 DNS DNS, Domain Name System, is a distributed database of TCP/IP application. DNS provides translation of Domain name to IP. DNS IPv6 DNS Serv

184 Dynamic DNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them

14 7800NXand7800NXL Port Meaning 1 Power Switch Power ON / OFF switch. 2 Power Connect the supplied power adapter to this jack. 3 RESET Afte

185 User can register different DDNS to different interfaces. Examples: Note first users have to go to the Dynamic DNS registration service provider t

186 DNS Proxy DNS proxy is used to forward request and response message between DNS Client and DNS Server. Hosts in LAN can use router serving as a D

187 Static ARP ARP (Address Resolution Protocol) is a TCP/IP protocol that allows the resolution of network layer addresses into the link layer addre

188 UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP o

189 Installing UPnP in Windows Example Follow the steps below to install the UPnP in Windows Me. Step 1: Click Start and Control Panel. Double-click

190 Step 5: Restart the computer when prompted. Follow the steps below to install the UPnP in Windows XP. Step 1: Click Start and Control Panel. Step

191 Step 5: In the Networking Services window, select the Universal Plug and Play check box. Step 6: Click OK to go back to the Windows Optional Netwo

192 Step 3: In the Internet Connection Properties window, click Settings to see the port mappings that were automatically created. Step 4: You may

193 in the system tray Step 6: Double-click on the icon to display your current Internet connection status.

194 Web Configurator Easy Access With UPnP, you can access web-based configuration for the BiPAC 7800(N)X(L) without first finding out the IP address

Notice Please read this notice before moving on next. You are now reading an all-in-one document on instructions about three different routers wi

15 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the fron

195 VPN (7800(N)X only) A virtual private network (VPN) is a private network that interconnects remote (and often geographically separate) networks

196 Click Add to create IPSec connections. IPSec Settings Connection Name: A given name for the connection (e.g. “connection to office”). WAN Interfa

197 Pre-Shared Key: This is for the Internet Key Exchange (IKE) protocol, a string from 4 to 128 characters. Both sides should use the same key. IKE i

198 authentication. Default is 60 minutes (3600 seconds). A short time increases security by forcing the two parties to update the keys. However, ever

199 Examples (7800NX for example): 1. LAN-to-LAN connection Two BiPAC 7800NXs want to setup a secure IPSec VPN tunnel Note: The IPSec Settings shal

200

201 Branch Office Side: Setup details: the same operation as done in Head Office side Item Function Description 1 Connection Name B-to-H Give a nam

202 2. Host to LAN Router servers as VPN server, and host should install the IPSec client to connect to head office through IPSec VPN. Item Functi

203

204 PPTP The Point-to-Point Tunneling Protocol (PPTP) is a Layer2 tunneling protocol for implementing virtual private networks through IP network. PP

16 Chapter 3: Basic Installation The router can be configured through your web browser. A web browser is included as a standard application in the

205 PPTP Account Connection Name: A user-defined name for the connection. Tunnel: Select Enable to activate the account. PPTP server is waiting for

206 PPTP Client PPTP client can help you dial-in the PPTP server to establish PPTP tunnel over Internet. Name: user-defined name for identification.

207 Example: PPTP Remote Access with Windows7 (Note: inside test with 172.16.1.208, just an example for illustration) Server Side: 1. Configurati

208 Client Side: 1. In Windows7 click Start > Control Panel> Network and Sharing Center, Click Set up a new connection network.

209 2. Click Connect to a workplace, and press Next. 3. Select Use my Internet connection (VPN) and press Next.

210 4. Input Internet address and Destination name for this connection and press Next.

211 5. Input the account (user name and password) and press Create.

212 6. Connect to the server.

213 7. Successfully connected. PS: You can also go to Network Connections shown below to check the detail of the connection. Right click “test” icon

214

17 Connecting Your Router Users can connect the ADSL2+ router as the following. 7800XADSL Router mode: Broadband Router mode:

215 Example: Configuring a LAN-to-LAN PPTP VPN Connection The branch office establishes a PPTP VPN tunnel with head office to connect two private net

216 Client Side: Branch Office The client user can set up a tunnel connecting to the PPTP server, and can also set the tunnel as the default route fo

217 GRE Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocol packets inside virtu

218 Certificate This feature is used for TR069 ACS Server authentication of the device using certificate, if necessary. If the imported certificate d

219 Click Import Certificate button to import your certificate. Enter the certificate name and insert the certificate.

220 Click Apply to confirm your settings.

221 Multicast Multicast is one of the three network transmission modes, Unicast, Multicast, Broadcast. It is a transmission mode that supports point-

222 group after it has received leave message. Robustness Value: Enter the router robustness parameter, 2-7, the greater the robustness value, the mor

223 Management SNMP Agent SNMP, Simple Network Management Protocol, is the most popular one in network. It consists of SNMP Manager，SNMP Agent and

224 TR- 069 Client TR-069 (short for Technical Report 069) is a DSL Forum (which was later renamed as Broadband Forum) technical specification entitle

18 3G/LTE Router mode

225 GetRPCMethods：Supported by both CPE and ACS, display the supported RFC listing methods. Click Apply to apply your settings.

226 Remote Access It is to allow remote access to the router to view or configure. Remote Access: Select “Enable” to allow management access from rem

227 Power Management Power management is a feature of some electrical appliances, especially computers that turn off the power or switch to a low-pow

228 Time Schedule The Time Schedule supports up to 32 timeslots which helps you to manage your Internet connection. In each time profile, you may sche

229 Diagnostics Push Service With push service, the system can send email messages with consumption data and system information. Recipient’s E-ma

230 Diagnostics Check the connections, including Ethernet connection, Internet Connection and wireless connection. Click Help link that can lead you

231 Fault Management IEEE 802.1ag Connectivity Fault Management (CFM) is a standard defined by IEEE. It defines protocols and practices for OAM (Oper

232 Restart This section lets you restart your router if necessary. Click in the low right corner of each configuration page. If you wish to res

233 Chapter 5: Troubleshooting If your router is not functioning properly, please refer to the suggested solutions provided in this chapter. If your

234 Problem with LAN interface Problem Suggested Action Cannot PING any PC on LAN Check the Ethernet LEDs on the front panel. The LED should be on

19 7800NXand7800NXL ADSL Router mode: Broadband Router mode:

235 Appendix: Product Support & Contact If you come across any problems please contact the dealer from where you purchased your product. Conta

20 3G/LTE Router mode

21 Network Configuration Configuring a PC in Windows 7 1. Go to Start. Click on Control Panel. Then click on Network and Interne

22 IPv4: 4. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties 5. In the TCP/IPv4 properties window, select the Obtain an IP

23 IPv6: 4. Select Internet Protocol Version 6 (TCP/IPv6) then click Properties 5. In the TCP/IPv6 properties window, select the Obtain an

24 Configuring a PC in Windows Vista 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at the top bar. 3. When the Netw

Table of Contents Chapter1:Introduction ...

25 IPv4: 5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an

26 IPv6: 8. Select Internet Protocol Version 6 (TCP/IPv6) then click Properties. 9. In the TCP/IPv6 properties window, select the Obtain

27 Configuring a PC in Windows XP IPv4: 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connect

28 IPv6: IPv6 is supported by Windows XP, but you should install it first. Act as shown below: 1. On the desktop, Click Start > Run, type cmd, th

29 Configuring PC in Windows 2000 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and Dial-up Conne

30 Configuring PC in Windows 95/98/Me 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and choose th

31 Configuring PC in Windows NT4.0 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and choose th

32 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface (Username and Password)

33 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown in the table. IPv4 LAN

34 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of s

DHCP ... 6

35 Easy Sign On (EZSO) This special feature makes it easier for you to configure your router so that you can connect to the internet in a matter of

36 3. Wait while the device is configured (DSL synchronized). 4. WAN port configuration is success and next to wireless, if you want skip wireless

37 6. Success in configuring the EZSO. Click link 192.168.1.254, it will lead you to the following page.

38 Ethernet mode 1. Select Ethernet, press Continue to go on to next step. 2. Enter the username, password from your ISP, for IP and DNS settings,

39 5. After the configuration is successful, click Next to Wireless button and you may proceed to configure the Wireless setting. Enable wireless and

40 Click 192.168.1.254, it will lead you to the following page.

41 3G/LTE 1. Select 3G/LTE, press Continue to go on to next step. 2. Enter the APN, username, password from your ISP, for settings about Authentica

42 5. After the configuration is successful, click Next to Wireless button and you may proceed to configure the Wireless setting. Enable wireless and

43 Click 192.168.1.254, it will lead you to the following page.

44 Chapter 4: Configuration Configuration via Web Interface Open your web browser; enter the IP address of your router, which by default is 192.168

DMZHost ... 174One‐to‐On

45 Once you have logged on to your BiPAC 7800(N)X(L) Router via your web browser, you can begin to set it up according to your requirements. On the c

46 Status This Section gives users an easy access to the information about the working router and access to view the current status of the router. H

47 Summary The basic information about the device is provided here (the following is a configured screenshots to let users understand clearly).

48 WAN This table displays the information of the WAN connections, users can turn here for WAN connection information. Interface: The WAN connecti

49 Statistics LAN The table shows the statistics of LAN. Note: P4 can be configured as EWAN, and when the device is in EWAN profile, there is no P4

50 WAN Service The table shows the statistics of WAN. Interface: Display the connection interface. Description: the description for the connection

51 xDSL Mode: Modulation protocol, including G.dmt, G.lite, T1.413, ADSL2, AnnexL, ADSL2+ and AnnexM. Traffic Type: transfer mode, here supports A

52 K (number of bytes in DMT frame): show the number of bytes in DMT frame. R (number of check bytes in RS code word): show the number of check bytes

53 When it is OK, the following test result window will appear. You can view the quality of ADSL connection. Here the connection is OK. Reset: Click

54 Bandwidth Usage Bandwidth Usage provides users direct view of bandwidth usage with simple diagram. Bandwidth usage shows the use of the bandwidth

1 Chapter 1: Introduction Introduction to your Router The BiPAC 7800(N)X(L) is a fibre-ready ADSL2+ modem, an all-in-one advanced device integrating

55 When you press View WAN Traffic concurrently button, the WAN Bandwidth Usage pops up so that users can view the WAN traffic concurrently.

56 WAN Service Press View WAN Transmitted button to change the diagram to the statistics from a Received Bytes of view.

57 Press View LAN Traffic concurrently button to directly switch to the LAN Bandwidth Usage page to view the LAN traffic concurrently.

58 3G/LTE Status Status: The current status of the 3G/LTE card. Signal Strength: The signal strength bar indicates current 3G signal strength. Ne

59 Route Destination: The IP address of destination network. Gateway: The IP address of the gateway this route uses. Subnet Mask: The destination

60 ARP This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (M

61 DHCP The DHCP Table lists the DHCP lease information for all IP addresses assigned by the DHCP server in the device. Host Name: The Host Name

62 IPSec (7800(N)X only) Name: The IPSec connection name. Active: Display the connection status. Local Subnet: Display the local network. Remote Su

63 PPTP (7800(N)X only) PPTP Server Name: The PPTP connection name. Enable: Display the connection status with icons. Status: The connection statu

64 Log System Log Display system logs accumulated up to the present time. You can trace historical information with this function. And the log polic

2 Jumbo frames supported Jumbo frames are Ethernet frames with more than 1500 bytes (standard Ethernet frame) of payload. Conventionally, jumbo frames

65 Security Log Security log displays the message logged about security, like filter messages and some firewall message. You can turn to IP Filtering

66 Quick Start Quick Start This part allows you to quickly configure and connect your router to internet. DSL mode 1. Select DSL, press Continue

67 3. Wait while the device is configured. 4. WAN port configuration is successful. 5. After the configuration is successful, click Next to Wirel

68 If Quick Start is finished, user can turn to Status > Summary to see the basic information.

69 Ethernet mode 1. Select Ethernet, press Continue to go on to next step, or if you only want to configure Wireless, press Jump to Wireless setting.

70 5. After the configuration is successful, click Next to Wireless button and you may proceed to configure the Wireless setting. Enable wireless and

71 3G/LTE 1. Select 3G/LTE, press Continue to go on to next step, or if you only want to configure Wireless, press Jump to Wireless setting. 2. Sel

72 5. After the configuration is successful, click Next to Wireless button and you may proceed to configure the Wireless setting. Enable wireless and

73 Configuration When you click this item, the column will expand to display the sub-items that will allow you to further configure your router. LA

74 LAN - Local Area Network A Local Area Network (LAN) is a shared communication system network where many computers are connected. This type of net

3 Features • Triple-WAN ports for 3G/4G LTE, ADSL2+, Gigabit Ethernet WAN (EWAN) for broadband connectivity • Gigabit WAN and LAN • Fibre (FTTC/FTT

75 CPE from the specified LAN group. DHCP Server You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the route

76 assigned should be outside the range of 192.168.1.100-192.168.1.199. IP Alias This function allows the creation of multiple virtual IP interfa

77 IPv6 Autoconfig The IPv6 address composes of two parts, the prefix and the interface ID. There are two ways to dynamically configure IPv6 addres

78 available. Stateless: If selected, the PCs in LAN are configured through RA mode, thus, the PCs in LAN are configured through RA mode, to obtain

79 Stateless and Stateful IPv6 address Configuration Stateless: Two methods can be carried.  With DHCPv6 disabled, but Issue Router Advertisement

80 Stateful: two methods can be adopted.  With only DHCPv6 enabled With this method, the PCs’ addresses are configured the same as in IPv4, that i

81 Interface Grouping Interface grouping is a function to group interfaces, known as VLAN. A Virtual LAN, commonly known as a VLAN, is a group of h

82 Click Add to add groups. Group Name: Type a group name. Grouped WAN Interfaces: Select from the box the WAN interface you want to applied in the

83 In group "test", P2 and PPP0.1 are grouped in one group, they have their only network , see LAN. If you want to remove the group, chec

84 Wireless (7800NX(L) only) This section provides you ways to configure wireless access. The BiPAC 7800NX(L) supports wireless on the 2.4GHz for us

4 Network Protocols and Features • IPv4 or IPv4 / IPv6 Dual Stack • NAT, static (v4/v6) routing and RIP-1 / 2 • IPv6 Stateless / Stateful Address Aut

85 Basic It let you determine whether to enable Wireless function and set the basic parameters of an AP and the Virtual APs. Wireless: Default set

86 simultaneously. Where APs are shared by multiple providers, Virtual APs provide each provider with separate authentication and accounting data for

87 Security Wireless security prevents unauthorized access or damage to computers using wireless network. Note： The WPS feature will also be unav

88  Shared This is similar to network authentication “Open”. But here the WEP Encryption must be enabled.  802.1x RADIUS Server IP Address:

89  WPA WPA Group ReKey Internal: The period of renewal time for changing the security key automatically between wireless client and Access Point

90  WPA2 WPA2 Preauthentication: When a wireless client wants to handoff to another AP, with preauthentication, it can perform 802.1X authenticati

91 RADIUS Server IP Address: RADIUS( Remote Authentication Dial In User Service), Enter the IP address of RADIUS authentication server. RADIUS Server

92 WPS Setup WPS (Wi-Fi Protected Setup) feature is a standard protocol created by Wi-Fi Alliance. WPS is used to exchange the AP setting with Statio

93 Configure AP as Registrar Add Enrollee with PIN method 1. Select radio button “Enter STA PIN”. 2. Input PIN from Enrollee Station (16837546 in

94 4. Operate Station to start WPS Adding Enrollee. Launch the wireless client’s WPS utility (eg.Ralink Utility). Set the Config Mode as Enrollee, p